Initial project setup

managed_components/espressif__tinyusb/hw/bsp/stm32u0/boards/stm32u083cdk/STM32U083MCTx_FLASH.ld

@@ -0,0 +1,176 @@
+/**
+  ******************************************************************************
+  * @file      LinkerScript.ld
+  * @author    Auto-generated by STM32CubeIDE
+  * @brief     Linker script for STM32U083MCTx Device from STM32U0 series
+  *            256KBytes FLASH
+  *            40KBytes RAM
+  *
+  *            Set heap size, stack size and stack location according
+  *            to application requirements.
+  *
+  *            Set memory bank area and size if external memory is used
+  ******************************************************************************
+  * @attention
+  *
+  * Copyright (c) 2023 STMicroelectronics.
+  * All rights reserved.
+  *
+  * This software is licensed under terms that can be found in the LICENSE file
+  * in the root directory of this software component.
+  * If no LICENSE file comes with this software, it is provided AS-IS.
+  *
+  ******************************************************************************
+  */
+
+/* Entry Point */
+ENTRY(Reset_Handler)
+
+/* Memories definition */
+MEMORY
+{
+  RAM    (xrw)    : ORIGIN = 0x20000000,   LENGTH = 40K
+  FLASH    (rx)    : ORIGIN = 0x8000000,   LENGTH = 256K
+}
+
+/* Highest address of the user mode stack */
+_estack = ORIGIN(RAM) + LENGTH(RAM); /* end of "RAM" Ram type memory */
+
+_Min_Heap_Size = 0x200;  /* required amount of heap */
+_Min_Stack_Size = 0x800; /* required amount of stack */
+
+/* Sections */
+SECTIONS
+{
+  /* The startup code into "FLASH" Rom type memory */
+  .isr_vector :
+  {
+    . = ALIGN(4);
+    KEEP(*(.isr_vector)) /* Startup code */
+    . = ALIGN(4);
+  } >FLASH
+
+  /* The program code and other data into "FLASH" Rom type memory */
+  .text :
+  {
+    . = ALIGN(4);
+    *(.text)           /* .text sections (code) */
+    *(.text*)          /* .text* sections (code) */
+    *(.glue_7)         /* glue arm to thumb code */
+    *(.glue_7t)        /* glue thumb to arm code */
+    *(.eh_frame)
+
+    KEEP (*(.init))
+    KEEP (*(.fini))
+
+    . = ALIGN(4);
+    _etext = .;        /* define a global symbols at end of code */
+  } >FLASH
+
+  /* Constant data into "FLASH" Rom type memory */
+  .rodata :
+  {
+    . = ALIGN(4);
+    *(.rodata)         /* .rodata sections (constants, strings, etc.) */
+    *(.rodata*)        /* .rodata* sections (constants, strings, etc.) */
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM.extab   : {
+    . = ALIGN(4);
+    *(.ARM.extab* .gnu.linkonce.armextab.*)
+    . = ALIGN(4);
+  } >FLASH
+
+  .ARM : {
+    . = ALIGN(4);
+    __exidx_start = .;
+    *(.ARM.exidx*)
+    __exidx_end = .;
+    . = ALIGN(4);
+  } >FLASH
+
+  .preinit_array     :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array*))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  .init_array :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT(.init_array.*)))
+    KEEP (*(.init_array*))
+    PROVIDE_HIDDEN (__init_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  .fini_array :
+  {
+    . = ALIGN(4);
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT(.fini_array.*)))
+    KEEP (*(.fini_array*))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+    . = ALIGN(4);
+  } >FLASH
+
+  /* Used by the startup to initialize data */
+  _sidata = LOADADDR(.data);
+
+  /* Initialized data sections into "RAM" Ram type memory */
+  .data :
+  {
+    . = ALIGN(4);
+    _sdata = .;        /* create a global symbol at data start */
+    *(.data)           /* .data sections */
+    *(.data*)          /* .data* sections */
+    *(.RamFunc)        /* .RamFunc sections */
+    *(.RamFunc*)       /* .RamFunc* sections */
+
+    . = ALIGN(4);
+    _edata = .;        /* define a global symbol at data end */
+
+  } >RAM AT> FLASH
+
+  /* Uninitialized data section into "RAM" Ram type memory */
+  . = ALIGN(4);
+  .bss :
+  {
+    /* This is used by the startup in order to initialize the .bss section */
+    _sbss = .;         /* define a global symbol at bss start */
+    __bss_start__ = _sbss;
+    *(.bss)
+    *(.bss*)
+    *(COMMON)
+
+    . = ALIGN(4);
+    _ebss = .;         /* define a global symbol at bss end */
+    __bss_end__ = _ebss;
+  } >RAM
+
+  /* User_heap_stack section, used to check that there is enough "RAM" Ram  type memory left */
+  ._user_heap_stack :
+  {
+    . = ALIGN(8);
+    PROVIDE ( end = . );
+    PROVIDE ( _end = . );
+    . = . + _Min_Heap_Size;
+    . = . + _Min_Stack_Size;
+    . = ALIGN(8);
+  } >RAM
+
+  /* Remove information from the compiler libraries */
+  /DISCARD/ :
+  {
+    libc.a ( * )
+    libm.a ( * )
+    libgcc.a ( * )
+  }
+
+  .ARM.attributes 0 : { *(.ARM.attributes) }
+}

managed_components/espressif__tinyusb/hw/bsp/stm32u0/boards/stm32u083cdk/board.cmake

@@ -0,0 +1,12 @@
+set(MCU_VARIANT stm32u083xx)
+set(JLINK_DEVICE stm32u083mc)
+
+set(LD_FILE_GNU ${CMAKE_CURRENT_LIST_DIR}/STM32U083MCTx_FLASH.ld)
+set(LD_FILE_IAR ${CMAKE_CURRENT_LIST_DIR}/stm32u083xx_flash.icf)
+
+function(update_board TARGET)
+  target_compile_definitions(${TARGET} PUBLIC
+    STM32U083xx
+    CFG_EXAMPLE_VIDEO_READONLY
+    )
+endfunction()

managed_components/espressif__tinyusb/hw/bsp/stm32u0/boards/stm32u083cdk/board.h

@@ -0,0 +1,129 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2020, Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+/* metadata:
+   name: STM32U083C-DK Discovery Kit
+   url: https://www.st.com/en/evaluation-tools/stm32u083c-dk.html
+*/
+
+#ifndef BOARD_H_
+#define BOARD_H_
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+// LED - using PA5 (Blue LED from CubeMX)
+#define LED_PORT              GPIOA
+#define LED_PIN               GPIO_PIN_5
+#define LED_STATE_ON          1
+
+// Button - using PC2 (from CubeMX generated code)
+#define BUTTON_PORT           GPIOC
+#define BUTTON_PIN            GPIO_PIN_2
+#define BUTTON_STATE_ACTIVE   0  // Active low (pressed = 0)
+
+// UART - using USART2 on PA2/PA3 (VCP TX/RX from CubeMX)
+#define UART_DEV              USART2
+#define UART_CLK_EN           __HAL_RCC_USART2_CLK_ENABLE
+#define UART_GPIO_PORT        GPIOA
+#define UART_GPIO_AF          GPIO_AF7_USART2
+#define UART_TX_PIN           GPIO_PIN_2
+#define UART_RX_PIN           GPIO_PIN_3
+
+//--------------------------------------------------------------------+
+// RCC Clock
+//--------------------------------------------------------------------+
+static inline void board_stm32u0_clock_init(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_CRSInitTypeDef RCC_CRSInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef  PeriphClkInit = {0};
+
+  /** Configure the main internal regulator output voltage
+  */
+  HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+  /** Initializes the RCC Oscillators according to the specified parameters
+  * in the RCC_OscInitTypeDef structure.
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_HSI48;
+  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
+  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+  RCC_OscInitStruct.HSI48State = RCC_HSI48_ON;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
+  RCC_OscInitStruct.PLL.PLLM = RCC_PLLM_DIV1;
+  RCC_OscInitStruct.PLL.PLLN = 8;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2;
+  RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV4;
+  HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+  /** Initializes the CPU, AHB and APB buses clocks
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
+
+  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
+
+  /** Enable the CRS clock
+  */
+  __HAL_RCC_CRS_CLK_ENABLE();
+
+  /** Configures CRS
+  */
+  RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1;
+  RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB;
+  RCC_CRSInitStruct.Polarity = RCC_CRS_SYNC_POLARITY_RISING;
+  RCC_CRSInitStruct.ReloadValue = __HAL_RCC_CRS_RELOADVALUE_CALCULATE(48000000,1000);
+  RCC_CRSInitStruct.ErrorLimitValue = 34;
+  RCC_CRSInitStruct.HSI48CalibrationValue = 32;
+  HAL_RCCEx_CRSConfig(&RCC_CRSInitStruct);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2;
+  PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+
+  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USB;
+  PeriphClkInit.UsbClockSelection = RCC_USBCLKSOURCE_HSI48;
+  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);
+}
+
+static inline void board_vbus_sense_init(void)
+{
+  // USB VBUS sensing not required for device-only operation
+}
+
+#ifdef __cplusplus
+ }
+#endif
+
+#endif /* BOARD_H_ */

managed_components/espressif__tinyusb/hw/bsp/stm32u0/boards/stm32u083cdk/board.mk

@@ -0,0 +1,13 @@
+MCU_VARIANT = stm32u083xx
+CFLAGS += \
+  -DSTM32U083xx
+
+# All source paths should be relative to the top level.
+LD_FILE = $(BOARD_PATH)/STM32U083MCTx_FLASH.ld
+LD_FILE_IAR = $(BOARD_PATH)/stm32u083xx_flash.icf
+
+# For flash-jlink target
+JLINK_DEVICE = STM32U083MC
+
+# flash target using on-board stlink
+flash: flash-stlink

managed_components/espressif__tinyusb/hw/bsp/stm32u0/boards/stm32u083cdk/stm32u083xx_flash.icf

@@ -0,0 +1,32 @@
+/*###ICF### Section handled by ICF editor, don't touch! ****/
+/*-Editor annotation file-*/
+/* IcfEditorFile="$TOOLKIT_DIR$\config\ide\IcfEditor\cortex_v1_0.xml" */
+/*-Specials-*/
+define symbol __ICFEDIT_intvec_start__ = 0x08000000;
+/*-Memory Regions-*/
+define symbol __ICFEDIT_region_ROM_start__ = 0x08000000;
+define symbol __ICFEDIT_region_ROM_end__   = 0x0803FFFF;
+define symbol __ICFEDIT_region_RAM_start__ = 0x20000000;
+define symbol __ICFEDIT_region_RAM_end__   = 0x20007FFF;
+
+/*-Sizes-*/
+define symbol __ICFEDIT_size_cstack__ = 0x800;
+define symbol __ICFEDIT_size_heap__   = 0x200;
+/**** End of ICF editor section. ###ICF###*/
+
+
+define memory mem with size = 4G;
+define region ROM_region      = mem:[from __ICFEDIT_region_ROM_start__   to __ICFEDIT_region_ROM_end__];
+define region RAM_region      = mem:[from __ICFEDIT_region_RAM_start__   to __ICFEDIT_region_RAM_end__];
+
+define block CSTACK    with alignment = 8, size = __ICFEDIT_size_cstack__   { };
+define block HEAP      with alignment = 8, size = __ICFEDIT_size_heap__     { };
+
+initialize by copy { readwrite };
+do not initialize  { section .noinit };
+
+place at address mem:__ICFEDIT_intvec_start__ { readonly section .intvec };
+
+place in ROM_region   { readonly };
+place in RAM_region   { readwrite,
+                        block CSTACK, block HEAP };