Initial project setup

managed_components/espressif__tinyusb/hw/bsp/saml2x/family.c

@@ -0,0 +1,172 @@
+/*
+ * The MIT License (MIT)
+ *
+ * Copyright (c) 2019 Ha Thach (tinyusb.org)
+ *
+ * Permission is hereby granted, free of charge, to any person obtaining a copy
+ * of this software and associated documentation files (the "Software"), to deal
+ * in the Software without restriction, including without limitation the rights
+ * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
+ * copies of the Software, and to permit persons to whom the Software is
+ * furnished to do so, subject to the following conditions:
+ *
+ * The above copyright notice and this permission notice shall be included in
+ * all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
+ * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
+ * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
+ * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
+ * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
+ * THE SOFTWARE.
+ *
+ * This file is part of the TinyUSB stack.
+ */
+
+/* metadata:
+   manufacturer: Microchip
+*/
+
+#include "sam.h"
+
+// Suppress warning caused by mcu driver
+#ifdef __GNUC__
+#pragma GCC diagnostic push
+#pragma GCC diagnostic ignored "-Wcast-qual"
+#endif
+
+#include "hal/include/hal_gpio.h"
+#include "hal/include/hal_init.h"
+#include "hpl/gclk/hpl_gclk_base.h"
+#include "hpl_mclk_config.h"
+
+#ifdef __GNUC__
+#pragma GCC diagnostic pop
+#endif
+
+#include "bsp/board_api.h"
+#include "board.h"
+
+//--------------------------------------------------------------------+
+// Forward USB interrupt events to TinyUSB IRQ Handler
+//--------------------------------------------------------------------+
+void USB_Handler(void) {
+  tud_int_handler(0);
+}
+
+//--------------------------------------------------------------------+
+// MACRO TYPEDEF CONSTANT ENUM DECLARATION
+//--------------------------------------------------------------------+
+
+/* Referenced GCLKs (out of 0~4), should be initialized firstly */
+#define _GCLK_INIT_1ST 0x00000000
+/* Not referenced GCLKs, initialized last */
+#define _GCLK_INIT_LAST 0x0000001F
+
+void board_init(void) {
+  // Clock init ( follow hpl_init.c )
+  hri_nvmctrl_set_CTRLB_RWS_bf(NVMCTRL, CONF_NVM_WAIT_STATE);
+
+  _set_performance_level(2);
+
+  _osc32kctrl_init_sources();
+  _oscctrl_init_sources();
+  _mclk_init();
+#if _GCLK_INIT_1ST
+  _gclk_init_generators_by_fref(_GCLK_INIT_1ST);
+#endif
+  _oscctrl_init_referenced_generators();
+  _gclk_init_generators_by_fref(_GCLK_INIT_LAST);
+
+#if (CONF_PORT_EVCTRL_PORT_0 | CONF_PORT_EVCTRL_PORT_1 | CONF_PORT_EVCTRL_PORT_2 | CONF_PORT_EVCTRL_PORT_3)
+  hri_port_set_EVCTRL_reg(PORT, 0, CONF_PORTA_EVCTRL);
+  hri_port_set_EVCTRL_reg(PORT, 1, CONF_PORTB_EVCTRL);
+#endif
+
+  // Update SystemCoreClock since it is hard coded with asf4 and not correct
+  // Init 1ms tick timer (samd SystemCoreClock may not correct)
+  SystemCoreClock = CONF_CPU_FREQUENCY;
+  SysTick_Config(CONF_CPU_FREQUENCY / 1000);
+
+  // Led init
+  gpio_set_pin_direction(LED_PIN, GPIO_DIRECTION_OUT);
+  gpio_set_pin_level(LED_PIN, !LED_STATE_ON);
+
+  // Button init
+  gpio_set_pin_direction(BUTTON_PIN, GPIO_DIRECTION_IN);
+  gpio_set_pin_pull_mode(BUTTON_PIN, BUTTON_STATE_ACTIVE ? GPIO_PULL_DOWN : GPIO_PULL_UP);
+
+#if CFG_TUSB_OS == OPT_OS_FREERTOS
+  // If freeRTOS is used, IRQ priority is limit by max syscall ( smaller is higher )
+  NVIC_SetPriority(USB_IRQn, configLIBRARY_MAX_SYSCALL_INTERRUPT_PRIORITY);
+#endif
+
+  /* USB Clock init
+   * The USB module requires a GCLK_USB of 48 MHz ~ 0.25% clock
+   * for low speed and full speed operation. */
+  hri_gclk_write_PCHCTRL_reg(GCLK, USB_GCLK_ID, GCLK_PCHCTRL_GEN_GCLK1_Val | GCLK_PCHCTRL_CHEN);
+  hri_mclk_set_AHBMASK_USB_bit(MCLK);
+  hri_mclk_set_APBBMASK_USB_bit(MCLK);
+
+  // USB Pin Init
+  gpio_set_pin_direction(PIN_PA24, GPIO_DIRECTION_OUT);
+  gpio_set_pin_level(PIN_PA24, false);
+  gpio_set_pin_pull_mode(PIN_PA24, GPIO_PULL_OFF);
+  gpio_set_pin_direction(PIN_PA25, GPIO_DIRECTION_OUT);
+  gpio_set_pin_level(PIN_PA25, false);
+  gpio_set_pin_pull_mode(PIN_PA25, GPIO_PULL_OFF);
+
+  gpio_set_pin_function(PIN_PA24, PINMUX_PA24G_USB_DM);
+  gpio_set_pin_function(PIN_PA25, PINMUX_PA25G_USB_DP);
+
+  // Output 500hz PWM on PB23 (TCC0 WO[3]) so we can validate the GCLK1 clock speed
+//  hri_mclk_set_APBCMASK_TCC0_bit(MCLK);
+//  TCC0->PER.bit.PER = 48000000 / 1000;
+//  TCC0->CC[3].bit.CC = 48000000 / 2000;
+//  TCC0->CTRLA.bit.ENABLE = true;
+//
+//  gpio_set_pin_function(PIN_PB23, PINMUX_PB23F_TCC0_WO3);
+//  hri_gclk_write_PCHCTRL_reg(GCLK, TCC0_GCLK_ID, GCLK_PCHCTRL_GEN_GCLK1_Val | GCLK_PCHCTRL_CHEN);
+}
+
+//--------------------------------------------------------------------+
+// Board porting API
+//--------------------------------------------------------------------+
+
+void board_led_write(bool state) {
+  gpio_set_pin_level(LED_PIN, state);
+}
+
+uint32_t board_button_read(void) {
+  // button is active low
+  return gpio_get_pin_level(BUTTON_PIN) ? 0 : 1;
+}
+
+int board_uart_read(uint8_t* buf, int len) {
+  (void) buf;
+  (void) len;
+  return 0;
+}
+
+int board_uart_write(void const* buf, int len) {
+  (void) buf;
+  (void) len;
+  return 0;
+}
+
+#if CFG_TUSB_OS == OPT_OS_NONE
+volatile uint32_t system_ticks = 0;
+void SysTick_Handler(void) {
+  system_ticks++;
+}
+
+uint32_t board_millis(void) {
+  return system_ticks;
+}
+
+#endif
+
+void _init(void) {
+
+}